ARTJET UV Printer Application 36 _ Vertical offset is not correct only for the right section of white
ARTJET UV Printer has been sold in Korea for 4 years, and we are organizing the printer problems we have encountered so far, their causes, and their solutions.
We have compiled 10 different print head problems and 17 ink supply problems, and you can find detailed information at the site below.
ARTJET UV Printer troubleshooting sum up
From last time, we are explaining not only UV printer problems and solutions, but also what products are produced with UV printers.
In the first session, ARTJET UV Printer Application 1 braille printing
In the second session, ARTJET UV Printer Application 2 Flip the material and align it
In the third session, ARTJET UV Printer Application 3 2.5D UV print
In the fourth session, Sai rip [Color Adjustment] tab. ARTJET UV Printer Application 4 Sai rip color graph
In the fifth session, ARTJET UV Printer Application 5 Sai rip print size compensation
In the sixth session, we talked about the acrylic bonding equipment that those who have UV printers and laser cutting equipment are looking for.
Hereuner is only Korean since only Korea is hot on this machine. ARTJET UV Printer Application 6 _아크릴 본딩 장비
In the seventh session ARTJET UV Printer Application 7 _ Ink Consumption Calculation
In the Eighth session, ARTJET UV Printer Application 8 _ I phone 14 print limitation
About K print, Korea Signage Label & special printing exhibition, ARTJET UV Printer Market research 1 _ K Print 2024 Korea printing exhibition
In the ninth session, ARTJET UV Printer Application 9 _ Mask printing not recommend
In the tenth session, ARTJET UV Printer Application 10 _ Leather Cigarette Case UV Printing
In the eleventh session, ARTJET UV Printer Application 11 _ Round soccer strategy board UV printing
In the twelve session, ARTJET UV Printer Application 12 _ What is ICC profile & menu board UV Printing
In the thirteen session, ARTJET UV Printer Application 13 _ Primer performance & limitation
In the fourteen session, ARTJET UV Printer Application 14 _ UV Print & Laser crop mark cutting
In the fifteen session, ARTJET UV Printer Application 15 _ Mobil case UV print profit
In the sixteen session, ARTJET UV Printer Application 16 _ Screen vs Digital Comparison and UV Printing on Hand Sanitizer Cases
In the seventeen session, ARTJET UV Printer Application 17 _ bottle print
In the eighteen session, ARTJET UV Printer Application 18 _ Canvas UV Printing
In the nineteen session, ARTJET UV Printer Application 19 _ Applying epoxy effect with varnish
In the twenty session, ARTJET UV Printer Application 20 _ Making a light frame with a printer+laser cutter
In the twenty one session, ARTJET UV Printer Application 21 _ UV Printer+Laser Cutting Equipment Button Name Tag Making
In the twenty two session, ARTJET UV Printer Application 21 _ UV Printer+Laser Cutting Making a Cell Phone Grip Tok
In the twenty three session, ARTJET UV Printer Application 23 _ UV Printer+Laser cutting Making an Acrylic Keychain
In the twenty four session, ARTJET UV Printer Application 24 _ UV Print with Zig
In the twenty five session, ARTJET UV Printer Application 25 _ How to make RD WORKS CCD camera cutting Video manual
In the twenty six session, ARTJET UV Printer Application 26 _ Acrylic bonding equipment
In the twenty seven session ARTJET UV Printer Application 27 _ All the steps to create UVDTF
In the twenty eight session ARTJET UV Printer Application 28 _ Simple troubleshooting & Captop replacement time
In the twenty nine session ARTJET UV Printer Application 29 _ UVDTF TEST Result
In the thirty session ARTJET UV Printer Application 30 _ Print head Anti crash system
In the thirty one session ARTJET UV Printer Application 31 _ Offset fine tune
In the thirty two session ARTJET UV Printer Application 32 _ ARTJET Delivery Preparation
In the thirty three session ARTJET UV Printer Application 33 _ ARTJET Setting Sequence
In the thirty four session ARTJET UV Printer Application 34 _ ARTJET CW+C Print time & ink cost
In the thirty five session ARTJET UV Printer Application 35 _ Create a white shield with different images on the front and back of the keyring
Today, I will explain the symptoms and solutions of problems that occur during printing, rather than the application.
I. Problem
ARTJET UV Printer Application 36 _ Vertical offset is not correct only for the right section of white 1
The horizontal length is 600mm,
As shown in the picture above, the white is not offset in the vertically, not horizontally, in the print start section.
and when moving away from the start section, the offset is correct in the vertical direction.
The representative who called said that after looking closely, the varnish is also not in the correct position, similar to white.
He said that if I print with single leave, uni direction, there is no problem, but if I print with bi direction, this problem occurs.
It was a problem I had never seen before, and I was confused because there was no pattern.
II. “I don’t think the scan speed was like this,”
1. The representative who gave me a clue to the solution
After trying various things to solve the problem, He called me and told me the suspicious point first.
“The scan speed is fast, but it says slow below,, but it wasn’t like this at first,,, is this correct?”
Thinking about that part, I understood the irregular problem symptom.
2. ARTJET Manual 24 pages
In the ARTJET manual, the speed settings for Scan speed and feed speed are marked in red as shown below.
When I first verified the equipment, I tested almost all the buttons, so if the above settings are wrong, it can cause problems such as stopping during printing, so I highlighted them in red.
The contents of the manual are as follows.
“Scan speed” is the speed at which the head carriage moves. Fast moves at approximately 1000mm per second, Normal moves at 800mm, and Slow moves at 400mm.
“Feed speed” is the speed at which the carriage moves once and then the flatbed moves at the feeding value during printing.
Must be,
* If Scan speed is Fast, Feed speed must also be set to Fast
* If Scan speed is Normal, Feed speed must also be set to Normal
* If Scan speed is Slow, Feed speed must also be set to Slow
3. Why is only the starting section a problem?
Scan speed FAST: The head carriage moves fast along the X-axis,
Feed speed SLOW: The flatbed moves slowly along the Y-axis.
The head carriage does not start after the flatbed is completely moved,
but starts printing as soon as the Y-axis flatbed receives the “start” signal.
That is, since the Y-axis flatbed is moving in the middle of printing, the vertical offset could not have been correct in the Start section.
Theoretically, it is correct that the vertical offset in the opposite direction is also incorrect,
but when printing in bi-directions, it seems that the Y-axis flatbed moved a little earlier because it was recognized as a single movement rather than a signal, and the vertical offset was correct.
III. ARTJET Basic Mode Normal
“Representative, the basic mode of ARTJET is Head carriage speed Normal, Feed speed Normal.
Head carriage FAST is possible, but it seems to be mechanically difficult, and Normal is the most stable.
And Slow didn’t have much of an improvement when I printed on materials with high stand off, so it’s better not to use it. “
“Yes, I understand.”
“Change both to Normal, Normal and leave a message to see if it works.”
That’s it for today.